Espoo, Finland — Nokia today announced that its Qt cross-platform User Interface (UI) and application framework for desktop and embedded platforms will be available under the Lesser General Public License (LGPL) version 2.1 license from the release of Qt 4.5, scheduled for March 2009. Previously, Qt has been made available to the open source community under the General Public License (GPL) license. In addition, Qt will now be available from the new domain, www.qtsoftware.com.

The move to LGPL licensing will provide open source and commercial developers with more permissive licensing than GPL and so increase flexibility for developers. In addition, Qt source code repositories will be made publicly available and will encourage contributions from desktop and embedded developer communities. With these changes, developers will be able to actively drive the evolution of the Qt framework.

Qt 4.5 will also be available under commercial licensing terms, while licensing for previous versions of Qt remains unchanged. In addition, service offerings for Qt will be expanded to ensure that all Qt development projects can have access to the same levels of support, independent of the selected license.

Good news for those of us too cheap to pay the $4950 per developer multi-platform license.

This page led me to a solution for this problem. In my case, I only needed to install the gsfonts-x11 package. Now Flash appears to be working correctly.

In Part I, our intrepid hero used Knoppix’s Linux Live CD to determine that the Toshiba Satellite A45-S130 would run Linux without any problems with incompatible hardware. At the end of Part I, we were led to believe our hero would next repartition the hard drive and possibly install Mandrake Linux¹.

First of all, I was unable to get the free partition tools to work. I resorted to using Partition Magic 8.0 to do the job.² Secondly, I decided to just install Knoppix on the hard disk and it was easy enough to make it look more or less like a standard Debian³ installation. The end result is I have a fully functional laptop running Linux which I’ve been using since September 2004

1. I currently have Mandrake installed on a Pentium 233.
2. Honestly, I really didn’t spend to much time getting the free partitioning tools to work since I already had Partition Magic. I also wanted to preserve the Windows XP partition because I occasionally have to use Windows for work.
3. I have Debian installed on a 486 (try installing a recent MS OS on a 486!)

I bought this Toshiba laptop back February because it supposedly works well with Linux. After 8 months of muddling along with Windows XP, I decided to get serious and install Linux. Rather than going through the trouble of repartitioning the hard disk and installing Linux only to find some obscure hardware incompatibility, I decided to try Knoppix’s Linux Live CD (basically a Linux distro that runs off a bootable CD).

Booting from the Knoppix CD is painless (hold ESC during boot, then press F1 to get into the BIOS setup to change the boot order). Knoppix boots successfully everything appears to work, including sound.

Getting connected to a wireless network

The A45-S130 comes with a Atheros 5001x wireless network interface and I’m using a D-Link DI-524 Wireless Broadband Router to share my DSL connection. The following steps worked for this configuration and might work for a similar setup.

First, I verified that the OS recognizes the hardware by running the commad (as root) iwconfig ath0.

ath0      IEEE 802.11  ESSID:""
          Mode:Managed  Frequency:2.412GHz  Access Point: 00:00:00:00:00:00
          Bit Rate:0kb/s   Tx-Power:off   Sensitivity=0/3
          Retry:off   RTS thr:off   Fragment thr:off
          Encryption key:off
          Power Management:off
          Link Quality=0/94  Signal level=-95 dBm  Noise level=-95 dBm
          Rx invalid nwid:0  Rx invalid crypt:0  Rx invalid frag:0
          Tx excessive retries:0  Invalid misc:0   Missed beacon:0


Getting the above output verifies that the OS at least sees the Atheros 5001x.

I decided to use the ifup / ifdown interface to start / stop the wireless network interface. This requires changing the /etc/network/interfaces file. I found the following /etc/network/interfaces works for me:

# /etc/network/interfaces -- configuration file for ifup(8), ifdown(8)

# The loopback interface
# automatically added when upgrading
auto lo ath0
iface lo inet loopback

iface ath0 inet dhcp
        pre-up /sbin/iwpriv ath0 mode 3
        pre-up /sbin/iwconfig ath0 essid MyEssid mode mananged key XXXXXXXXXXXXXXXXXXXXXXXXXX enc on


Replace MyEssid with your ESSID or network name and replace XXXXXXXXXXXXXXXXXXXXXXXXXX with your current encryption key (ascii keys wouldn’t work for me). Don’t forget to copy your new interfaces file to some sort of writable media, since Knoppix won’t save it!

Run ifup ath0 (as root) to bring up the interface. If there are no errors, then everything should be working.

So now I know everything should work, including wireless networking.

Stat tuned for Part II – Repartitioning the hard drive and installing a Linux distro (probably Mandrake).

Unfortunately xemacs would die horrible death if run under X. The solution to this problem was to rerun configure with following option: ‘–ldflags=-z nocombreloc’ (and of course remaking the whole thing). Now everything works fine.